Best Epoxy For Oil Pan Repair: 10 Options Compared

#1 · Best Overall

1. J-B Weld TankWeld

• Compatible Material: Metal
• Material Type: Plastic
• Form: Putty

Best for: Petroleum-exposed putty repairs.

Why it ranks #1: Its verified facts specifically state resistance to petroleum when fully cured; it sets in 5 minutes, cures in 1 hour, and tolerates up to 300°F.

TankWeld's cured formula resists petroleum and hydraulic fluid, enabling a putty repair for equipment exposed to those substances. The steel-reinforced, hand-mixable epoxy is listed for gas tanks, radiators and water tanks, sets in five minutes and cures in one hour.

Hand mixing turns the two-part putty into a moldable material for rebuilding or patching metal, while its ability to cure on wet and dry surfaces supports more repair situations. The petroleum and hydraulic-fluid resistance is specifically stated for the fully cured material, an important condition for any fluid-exposed application. It withstands temperatures up to 300°F and can be drilled, tapped, machined, ground, filed and painted after curing.

Skip it if you need a listed tensile strength above 900 PSI; Vicpricme Metal Glue specifies up to 4,680 PSI.

TankWeld fits buyers patching listed tanks or metal equipment where cured petroleum resistance and moldable putty are relevant. Its stated 900 PSI tensile strength is a boundary to consider for structural loading.

Listed on Amazon as: J-B Weld 8217 TankWeld Gas Tank Repair – 1 oz.,Dark Grey

#2 · Oil-Resistant Formula

2. Permatex 2-Ton Epoxy

• Compatible Material: Ceramic, Concrete, Fiberglass, Metal
• Material Type: Epoxy
• Form: Liquid

Best for: Oil-resistant clear rigid bonding.

Why it ranks #2: The listed formula resists oil, unleaded gasoline, mineral spirits, and antifreeze, with a 30-minute set and 1-hour cure.

Permatex 2-Ton Epoxy combines a clear finish with stated resistance to oil, unleaded gasoline, mineral spirits, antifreeze and salt solution, enabling rigid-material repairs where exposure resistance matters. Its repositionable formula allows adjustments for up to 15 minutes before it sets and cures.

The 30-minute set and one-hour cure make this a quicker schedule than epoxies requiring a day-long cure, while the 15-minute repositioning window helps correct alignment after joining parts. Its gap-filling, non-shrinking formula supports bonding rigid materials such as metal, fiberglass, ceramic and concrete. The listed tensile strength is up to 4,000 PSI, and the clear appearance can suit repairs where a gray metal-colored bond would be more visible.

Skip it if you need a steel-reinforced putty for molding a metal patch; J-B Weld SteelStik is a hand-mixable putty stick.

Choose Permatex 2-Ton when oil resistance, a clear finish and time to reposition rigid parts matter. It suits bonding and gap filling, but its stated application is rigid materials rather than flexible repairs.

Listed on Amazon as: Permatex 84133 2-Ton Epoxy

#3 · High-Heat Putty

3. J-B Weld SteelStik

• Compatible Material: Brick, Ceramic, Fiberglass, Metal, Plastic
• Material Type: Epoxy Resin
• Form: Stick

Best for: Fast hand-molded metal patching.

Why it ranks #3: Its metal-repair putty resists continuous temperatures up to 300°F and intermittent temperatures up to 450°F, with a stated 1-hour cure.

SteelStik is a hand-mixable, steel-reinforced epoxy putty that sets in about five minutes, enabling quick molding and rebuilding of metal parts. Its non-rusting formula and ability to resist continuous temperatures up to 300°F make it a compact putty option for shaping a patch directly onto a repair.

Kneading the two-part stick by hand avoids measuring liquid components, and the putty can be molded or built up to patch metal. Its one-hour cure gives a defined wait before further work, while the cured material can be shaped as needed for a component repair. SteelStik is also NSF-certified and safe for potable-water contact, an additional compatibility point for suitable equipment. Temperature resistance is listed at 300°F continuous and 450°F intermittent.

Skip it if you need a liquid adhesive for broad bonding surfaces; SteelStik is a hand-mixed putty intended for molding and rebuilding.

Pick SteelStik for a small, shaped metal patch where hand-moldable putty and a one-hour cure suit the workflow. Its 300°F continuous limit is an important boundary for parts exposed to sustained heat.

Listed on Amazon as: J-B Weld 8267 SteelStik Steel Reinforced Epoxy Putty Stick – 2 oz.

#4 · Cast-Metal Repair

4. AOJEL S300

• Compatible Material: Alloy Steel, Aluminum, Ceramic, Concrete…
• Material Type: Epoxy Metal-Filled Epoxy
• Form: Epoxy

Best for: Rigid aluminum rebuild repairs.

Why it ranks #4: It is specified for rigid aluminum, steel, stainless steel, and cast iron repairs, with waterproofing and heat resistance listed to 392°F.

AOJEL S300 pairs a structural, metal-filled epoxy with a seven-step repair protocol, enabling prepared rigid parts to be rebuilt rather than simply covered. It is specified for aluminum, steel, stainless steel, cast iron and cast aluminum, making it a targeted option when a damaged metal housing or casting needs a rigid repair.

The Repair Control protocol runs from preparation and purging through mixing, building, alignment, clamping and curing, giving the user an explicit sequence for forming a repair. Its true 1:1 mix and included plunger and spatula support controlled dispensing and blending. After cure, the material is drillable, sandable, fileable and paintable, so the repaired area can be finished or worked further. The stated heat resistance is up to 392°F; the listed use is rigid, non-flexing repair.

Skip it if you need a flexible repair or a putty stick to mold by hand; this epoxy is specified for rigid, non-flexing work.

Choose S300 when a prepared rigid metal part needs rebuilding and you value a guided mix-and-clamp process plus machinable finishing. Its fit is narrower for flexible or moving components, which fall outside its stated repair use.

Listed on Amazon as: S300 Structural Metal Epoxy for Aluminum & Steel, Cold Weld, 1.69 oz

#5

5. J-B Weld Original 8281

• Compatible Material: Ceramic, Metal, Plastic, Polyvinyl Chloride…
• Material Type: Epoxy
• Form: Paste

Best for: Larger-volume general metal repairs.

Why it ranks #5: Its two-part steel-reinforced formula is listed for automotive and metal repairs; it sets in 4–6 hours and cures in 15–24 hours.

J-B Weld Original in professional-size tubes supplies a two-part cold-weld system for automotive, household and marine repairs, enabling larger-volume work with the familiar 1:1 mix. It bonds metal and several other materials, then can be shaped, tapped, filed, sanded or drilled after curing.

The 10-ounce professional-size offering suits jobs that call for more material than a small repair tube, while the 1:1 ratio gives a straightforward mixing workflow. It sets in 4–6 hours and cures in 15–24 hours, so plan for a repair that remains undisturbed through that longer cure window. Once cured, the epoxy can be tapped, filed, sanded and drilled, letting users finish or modify the bonded area rather than leaving it untouched.

Skip it if you need a repair to set within minutes; Permatex 84109 sets in four minutes and requires no clamping.

This J-B Weld size suits buyers handling substantial automotive or household repair work who can allow a full cure period. Choose it for rigid, multi-surface bonding, not when a quick turnaround is the main requirement.

Listed on Amazon as: J-B Weld 8281 Professional Size Steel Reinforced Epoxy – Hardener and Steel Pack – 10 oz

#6

6. J-B Weld Original 8265S

• Compatible Material: Ceramic, Concrete, Fiberglass, Metal…
• Material Type: Steel
• Form: Gel, Liquid

Best for: Versatile cold-weld tube repairs.

Why it ranks #6: This two-part cold-weld epoxy is intended for automotive and metal repairs and can be shaped, tapped, filed, sanded, and drilled after curing.

J-B Weld Original uses a 1:1 two-part mix to create a cold-weld bond across metal and several other materials, enabling repairs without torch welding. It suits automotive, marine and household jobs, then can be tapped, filed, sanded or drilled after its extended cure.

The tube system mixes at a 1:1 ratio and sets in 4–6 hours, followed by a 15–24-hour cure, so this is a repair for users able to wait before finishing. Its listed compatible materials include metal, ceramic, concrete, fiberglass, plastic and wood, broadening its use beyond a single substrate. After curing, the bond can be shaped, tapped, filed, sanded and drilled, supporting later adjustment or finishing.

Skip it if you need a moldable putty that cures in one hour; J-B Weld SteelStik lists a one-hour cure.

Original suits buyers seeking a versatile cold-weld adhesive for automotive, marine or household repairs and who can accommodate its cure time. It is a broad material option, not a fast-setting repair.

Listed on Amazon as: J-B Weld 8265S Original Cold-Weld Steel Reinforced Epoxy – 2 oz.

#7

7. Permatex PermaPoxy 4 Minute

• Compatible Material: Aluminum,stainless Steel,metal,steel
• Material Type: Plastic
• Form: Paste

Best for: Quick no-clamp multi-metal fixes.

Why it ranks #7: It bonds metal, fills gaps, and reaches up to 4500 PSI, but its listed temperature range ends at 300°F and it sets in only 4 minutes.

Permatex PermaPoxy 4 Minute sets without clamping, enabling quick assembly of multi-piece metal repairs when holding parts in place is difficult. The two-part, gap-filling epoxy bonds aluminum, stainless steel and steel, and its cured material can be drilled, sanded, threaded or filed.

A four-minute set and no-clamp application support jobs where a long hold is inconvenient, though they leave little time for positioning once mixed. The formula fills gaps without shrinking, helping bridge uneven mating surfaces. Its stated temperature range runs from -60°F to 300°F, and it is water- and solvent-resistant. Once cured, the repair can be drilled, sanded, threaded or filed for practical finishing or hardware installation.

Skip it if you need extended time to align and clamp parts; vicpricme Metal Glue lists a 30-minute working time.

PermaPoxy suits buyers making compact multi-metal repairs where quick set and no clamping simplify assembly. The short working time is the key boundary: prepare alignment and surfaces before mixing.

Listed on Amazon as: Permatex 84109 PermaPoxy 4 Minute Multi-Metal Epoxy, 0.84 oz.

#8

8. Vicpricme Metal Glue

• Compatible Material: Aluminum, Iron, Stone…
• Material Type: Epoxy Resin
• Form: Epoxy

Best for: Adjustable metal bonding repairs.

Why it ranks #8: This 1:1 metal epoxy is listed for aluminum, steel, and cast iron, with 30 minutes of working time and a 24-hour cure.

Vicpricme's 30-minute working time lets users align and clamp rigid parts before its 24-hour cure, enabling deliberate positioning on a metal repair. The 1:1 epoxy bonds aluminum, steel, stainless steel and cast iron, and cures to a drillable, sandable, fileable and paintable finish.

A true 1:1 mix keeps preparation straightforward, while the half-hour working window gives more time to align parts or build thickness than a quick-set adhesive. After the stated 24-hour cure, the dense repair can be drilled, sanded, filed or painted, supporting finishing work around a repaired component. The product lists up to 4,680 PSI strength and compatibility with several rigid materials, including metals, wood, ceramic, glass and concrete.

Skip it if you need a fast-setting repair that avoids clamping; Permatex 84109 sets in four minutes with no clamping needed.

This epoxy fits buyers who want time to position or build up a rigid metal repair and can wait through the full cure. Its listed use is rigid bonding, so it is not a flexible-parts solution.

Listed on Amazon as: Vicpricme Metal Glue, 2-Part Epoxy, 4,680 PSI Heavy-Duty Repair

#9

9. PC-7 Epoxy

• Compatible Material: Brick, Concrete, Fiberglass, Glass, Plastic…
• Material Type: Epoxy Resin
• Form: Liquid

Best for: Waterproof vertical-surface repairs.

Why it ranks #9: Its high-viscosity two-part formula is described for durable, waterproof repairs, but the supplied specifications do not state oil resistance or a temperature limit.

PC-7's high-viscosity, waterproof epoxy is suited to demanding repairs on vertical or overhead surfaces, enabling a spreadable bond where a thinner liquid can be difficult to keep in place. Its listed applications include stone, metal and tile, with bonding, sealing and repair uses.

The two-part resin offers a high-viscosity consistency, which supports application to vertical and overhead areas without relying on a runny coating. Its waterproof property makes it relevant to repairs exposed to water or moisture, while the multipurpose description covers bonding, sealing and repairing. PC-7 is also listed for brick, concrete, fiberglass, glass, plastic, rubber and stone. The product information does not specify a cure time, so the work schedule cannot be planned from a stated set window.

Skip it if you need a stated set time to schedule a fast repair; Permatex 84109 specifies a four-minute set.

PC-7 fits buyers applying waterproof epoxy to a vertical or overhead repair involving listed materials such as metal, stone or tile. Because no cure time is supplied, it is less suitable when a precise turnaround must be planned.

Listed on Amazon as: 1/2 Lb. PC-7 Epoxy

#10

10. J-B Weld MarineWeld

• Compatible Material: Alloy Steel, Aluminum, Metal, Plastic, Wood
• Material Type: Epoxy Resin
• Form: Paste

Best for: Marine and watercraft metal repairs.

Why it ranks #10: It bonds metal and other materials, but its marine-focused listing provides no oil-resistance or temperature specification for this use.

J-B Weld MarineWeld is a two-part cold-weld epoxy specified for marine and watercraft repairs, enabling bonding across metal, composites and fiberglass. Its 1:1 tube mix sets in 4–6 hours and cures in 16–24 hours, after which the dark-gray repair can be worked further.

The marine-focused use makes this a relevant option for watercraft components, while compatibility with alloy steel, aluminum, metal, plastic and wood adds flexibility for mixed-material repairs. The 1:1 mix is straightforward, but the 4–6-hour set and 16–24-hour cure call for a planned repair window. Once cured, MarineWeld can be tapped, filled, sanded, molded and drilled, allowing finishing or shaping after the bonded area has hardened.

Skip it if you need an epoxy with listed oil resistance for an oil-exposed repair; Permatex 84133 lists resistance to oil.

MarineWeld suits watercraft owners repairing compatible metal or mixed-material components who can leave the work through its cure period. Its marine emphasis is useful, but the supplied facts do not list oil resistance.

Listed on Amazon as: J-B Weld 8272 MarineWeld Marine Epoxy – 2 oz.